在线中文字幕日本无码欧美

全國服務熱線:

18396804865 錢經理

如何延長數控切割機使用的壽命

2021-01-20 15:58:53文章來源:www.adviceforagents.com780

根據使用說明書的要求,采取合理的切線距離,切斷與切割噴嘴和工件表面的距離,當穿孔時,盡量使用2倍的正常切割距離,或采用等離子弧可以達到很高高度.數控切割等離子的正確壓力和流量對耗材的使用壽命很重要.如果壓力過高,電極的壽命將大大降低.壓力太低,噴嘴的壽命會受到影響.推薦閱讀: 使用數控火焰切割機時應注意些什么
According to the requirements of the instructions, reasonable tangent distance should be adopted to cut off the distance from the cutting nozzle and the workpiece surface. When perforating, the normal cutting distance should be twice as long as possible, or plasma arc can be used to reach a high height. The correct pressure and flow rate of plasma in NC cutting are very important for the service life of consumables. If the pressure is too high. If the pressure is too low, the life of the nozzle will be affected. Recommended reading: What should we pay attention to when using the numerical control flame cutting machine
切割機不能在超過工作厚度的鋼板上打孔,正常的穿孔厚度是正常切削厚度的1/2.為了使噴嘴超載(即超過噴嘴的工作電流),噴嘴很快就會損壞.電流強度適用于噴嘴工作電流的95%.例如,對100A噴嘴的電流強度應設置150A的電路.
Cutting machine can't punch holes on the steel plate which exceeds the working thickness. The normal punching thickness is 1/2 of the normal cutting thickness. In order to make the nozzle overload (i.e. exceed the working current of the nozzle), the nozzle will soon be damaged. The current intensity is suitable for 95% of the working current of the nozzle. For example, 150A circuit should be set for the current intensity of 100A nozzle.
等離子系統需要干燥和潔凈的等離子體可以正常工作,數控切割臟污通常氣體壓縮系統的問題,它會縮短易損件的使用壽命,非正常損壞.測試氣體質量的測試方法是割炬處于狀態,鏡子放在它的下部,消耗割炬內的氣體,如果出現在鏡子上的水分和霧,你就需要找出原因和正確.
The plasma system needs dry and clean plasma to work properly. CNC cutting dirty contamination is usually a problem of gas compression system. It will shorten the service life of vulnerable parts and cause abnormal damage. The test method of gas quality is that the cutting torch is in state, the mirror is placed at the bottom of the torch, and the gas in the cutting torch is consumed if it appears in the mirror. Water and fog on it, you need to find out the reason and the right one.
盡可能從邊緣處不刺.以邊緣為出發點,延長消費品的使用壽命.正確的方法是將噴嘴直接對準工件的邊緣,然后啟動等離子弧.在電弧開始時,噴嘴和電極消耗非???開始前,割炬應放置在切削金屬的距離處.
Starting from the edge, extend the service life of consumer goods. The correct way is to direct the nozzle to the edge of the workpiece, and then start the plasma arc. At the beginning of the arc, the nozzle and the electrode consume very fast. Before the beginning, the torch should be placed at the distance of the cutting metal.
防噴化學涂層有助于減少保護殼上的積渣.但是,在割炬噴上數字控制之前,必須將保護殼去掉.如果等離子弧僅延伸到工件表面,等離子弧將在切割的開始和結束時產生拉伸和延伸,這將對噴嘴造成不正常的損害.采用正確的邊啟動技術,選擇合適的"弧"信號時間,可以避免這一問題的發生.
Blowout-proof chemical coating helps to reduce slag deposit on the protective shell. However, the protective shell must be removed before the torch is sprayed with digital control. If the plasma arc only extends to the surface of the workpiece, the plasma arc will stretch and extend at the beginning and end of the cutting, which will cause abnormal damage to the nozzle. The correct side-start technique is adopted. The problem can be avoided by choosing the appropriate arc signal time.http://www.adviceforagents.com

  濟南卓然天成是大型數控火焰切割機廠家,數控等離子切割機廠家,便攜式數控切割機廠家www.adviceforagents.com,供應河北數控火焰切割機,山西數控等離子切割機,遼寧便攜式數控切割機,吉林數控火焰切割機,黑龍江數控等離子切割機,江蘇數控切割機,浙江數控切割機,安徽數控切割機,福建切割機,江西切割機,山東數控切割機,臺灣切割機,河南切割機,湖北數控切割機,湖南數控切割機,廣東切割機,海南數控切割機,四川數控切割機,貴州數控切割機,云南切割機,陜西切割機,甘肅數控切割機,青海數控切割機,需要的朋友聯系我們15254176866

電話咨詢
郵件咨詢
在線地圖
QQ客服
網站地圖 在线中文字幕日本无码欧美